|
|
|
|
Please call for details so we may assist in your choices.
Hydraulic Assist for L, U & C models: THE WAY to form 8’ or 10’ of 16ga or
any length heavier gage up to 10’ of 12ga. $3850 includes foot switch that can be used from either end of the brake (or deduct $100 for frame mounted switch). . Now you can form
DOWN FLANGE shapes including transverse duct by
creating openings in apron fingers and table blocks. See
literature for details on this optional build. Add to price of any model:
3’ & 4’ $1500,
5’ & 6’ $1900, 8’
$2400, 10’ $2700 . Rear Operated Manual Back Gauge With usable depth of 48” you can bend sheet metal at the same depth time and time again. Call if you need a depth of more than 48”. Add to price of any model: 3' & 4' $385, 5' & 6' $451, 8' & 10' $528 . .BOLT ON RADIUS BAR 1/16" to 1/2" radius: 3’ or 4’
$104.50 5’
or 6’ $150.70
8’ or 10’ $254.10. Many more radius sizes are available - call for
quote. Note: Using a bolt on radius bar requires a Bolt On Apron Angle if the
radius is greater than 1/4” (1/2” diameter). See Bolt On Apron Angle below
for notes. Bolt on radius bars might not work above 20ga mild steel or .050
alum. Magnetic radius bars can be used at full rated capacity of the
brake and hold themselves on without bolting. They are also suitable for cutting
up into segments for use with finger brakes.
3’ $346.50, 4’ $404.80,
5’ $466.40, 6’ $520.30, 8’
$635.80, 10’ $ . RADIUS added to leading edge of clamp
or fingers: 3’
or 4’ $99,
5’ or 6’ $198,
8’ or 10’ $2 . 1/4" minimum reverse bend apron:
The
stock configuration for all models allows 1/2" minimum reverse bends. The 1/4"
minimum reverse bend option includes machining of the apron
to 1/4" and a bolt on insert to build the apron back out to 1/2". The additional
cost for brakes up to 4' is $165; 5' & 6' $205; 8' $270; 10' $330. Note:
The rated capacity of all models assumes using all provided inserts and apron
angles. When apron angle and insert are removed to form 1/4" reverse bends,
capacity is reduced to 24ga. . BOLT ON APRON ANGLE
is included on all models except 3’ to 6’ 20ga. For $18 per foot you can add
a bolt on apron angle to your 3’ to 6’ 20ga brake. It will increase the
full-length capacity to 18ga. This option will be needed if using a bolt on
radius bar larger than 1/2” diameter on 3’ - 6’ 20ga models. All other
models already include a bolt on apron angle. . Counter
Weight(s) are INCLUDED on all 16ga, 14ga & 12ga, models and optional on all others: for 20ga & 18ga 3' or 4' Brakes and 22ga 6' $55 ea; for 20ga & 18ga 5' or 6' Brakes $88 ea; for 14ga and up Please Call for quote. . LEG KIT For 3' or 4'
16ga & lighter brakes* (All other models are built on
legs) 55
lbs. for $ *
Exception: L & U 48” 16ga are available as floor models with welded on legs that
weigh 110 lbs. for $ . SPECIAL 4" CUT BACK FINGER to bend 3/16" mild steel up to 4" wide without adjusting set back or clamp pressure is included with U models, and is optional for 16ga BP models: Up to 14ga $38.50; for 12ga $49.50. . COMPLETE SET OF FINGERS U & BP models: for
20ga & 16ga models: 3’ $184.50,
4’ $198, 5’
$247.50, 6’ $297,
8’ $402.60, 10’ $500.50
for
14ga & 12ga models: 3’
$239.80, 4’ $257.40,
5’ $321.20,
6’ $385,
8’ $525.80, 10’ $652.30 Additional stock fingers 2", 3" or 4" for U & BP models:
20ga
to 16ga $28.6ea
14ga to 12ga $41.80ea . FULL LENGTH FINGER U & BP brakes: 20ga & 16ga: 3’ or 4’
$170.50, 5’ or 6‘ $385, 8’ $335.50,
10’ $403.70. 14ga
& 12ga add 30% Additional
FINGERS for C6 models: Any combination: up to 36” $1237.50; 4’ $1197.90; 6’
$1982.20; 8’ $2250.60;
10’ $ ASK ABOUT THE RADIUS BRAKE: w/ 5 radii up to 6 ft $1969, 8 ft $2376; 10’ w/2 radii $3080
|
|
Details [ Prices ] [ Options ] Straight Brakes [ S Series ] [ L Series ] Finger Brakes [ BP Series ] [ U Series ] [ C Series ] Brake Options [ TD Option ] [ Hydraulic Assist Option ] [ Radius Brake ] [ Bead Roller ] Copyright © 2001
ProFormer, LLC
|